'cnc sl2 mori seiki 2000g control'

cnc sl2 mori seiki 2000g control

william rachels (63.24.62.204) -

Has anyone had a problem with the older sl2 mori seki(1970 something) lathes loosing the parameters and the program? poooff everything gone???this lathe has the yasnac control 2000g.

memory board shot maybe ??

And any good sites where to buy vintage replacement parts?

Any help would be greatly appreciated.

Thanks ,William

Comment #1 Bill (71.116.45.215) -

Maybe a bad battery backup. Ive seen this when the battery gets

old and the power flickers

Comment #2 william (63.24.113.80) -

thanks Bill for info,I did check the battery back-up and it checks at 3v.which is ok.What I did find out that it was a memory board which I purchased at yaskawa,exchange for about $1300.the machine is back up and running.some places I looked for the same board was $2800!(exchange).It pays to shop a little.

Comment #3 Oscar Quintanilla (189.163.204.74) -

Somebody can help me I need to get the manuals for a SL-3b with a yasnac 2000g control, If some body have info on this I will paid for a copy of this machine and control

thanks

Comment #4 Oscar Quintanilla (189.163.204.74) -

email oquinta@prodigy.net.mx

Comment #5 Dave K. (64.19.74.235) -

I need alarm codes for mori seiki 2 axis lathe.This number was on the controller MSX-850 111. This number was on the machine NL51FG2215.Can somebody help me>

Comment #6 vikas (59.94.252.220) -

I DONT HV OPERATOR MANUAL FOR 2000G NUMERICAL CONTROL FITTED IN SL2 MOREI SEIKI LATHE .I SHALL BE GREATFUL IF ANYBODY CAN HELP ME OUT OR ANY BODY WHO CAN HELP ME IN PROGRAMMING THE MACHINE

THANKS

Comment #7 ramon (201.160.223.16) -

quiero saber si me pueden ayudar, con una alarma num. 25 no se la pueso quitar

Comment #8 severiano perez (67.126.242.54) -

hello i nede in informechin hwo ken teike in alarm 0582 momory collating error

Comment #9 Mark Rice (70.251.7.28) -

Memory loss of Y2000G/G2 controls is often caused by loose cables

between the sections of the control, and e-proms backing out. Try

reseating all the cables and the proms (found on the master board

and the ladder board). Also check your 5 volts on your power suppluy. It should be 5.0 to 5.15 volts. Check it in the AC range

and make sure there is no ripple.

I have access to some operators and programming manuals, but they

are ratty (pages separated). I have a fairly complete copy of the

schematics, but it is a copy of a copy of a copy, so I have had

to pencil in places where it is hard to read. No, I don't have a

pff of them, they are some odd page size (neither B nor C) and

don't fit a scanner.

If you call Yaskawa, there are still a couple of guys who know

the control, but most of them won't tell you squat.

As far as the spindle drives go, just replace them with AC motor

and drive, and have done with it. It is cheaper than trying to

get those old drives and motors repaired.

Comment #10 JOSE (64.12.116.139) -

I JUST BOUGHT A 1982 MORI SEIKI SL3 WITH YASNAC 2000G I NEED ATIP OF WHAT SOFTWARE FOR MY COMPUTER TO PRORGRAM THANK YOU

Comment #11 Veravat (203.147.0.44) -

I want total alarm list CNC Mori Seiki , Model : CL2000B

Comment #12 Gus (68.0.146.204) - Sat Aug 23 23:53:51 2008

I have the manuals for an SL-4 with yasnac 2000g. I have had the machine since new and it is the best. I have been programing and running the machine and know it well. If you have specific questions maybe I can help. Se habla espanol.

Name:           
E-Mail:         

Optional (please add to our directory first)
Web Link:       
Link Title:     

Message:

Note: once you register your email address with CNC Machine it is used across our whole network of forums and blogs. You can create seperate profiles for each forum or blog, but use the same login.