'NUM 1040'

NUM 1040

Rafael Kilim (88.144.37.163) -

Help!

I have a Bumotec CNC milling machine (S91)Machine year 2001. We had a electric spark in the building electricty system and since then, the machine is displaying on the main NUM processer, with a red light light over the word HALT. Also, the screen only flickers for a second, but then it goes blank. It looks like all the software in the NUM controller etc has disapeared. Does anyone have any views? I would appreciate any help in this matter. I have no copy of the software, and wouldn't know how to load it.

Comment #1 mark (68.179.9.9) -

try circuit cnc in the uk

Comment #2 hatem (217.69.183.35) -

hello dear

i have one cnc drilling machine

i have a problem in the keyboard of NUM 720F

i don't know where can i get spare for this keyboard

i contact num company but no one reply

can u help?

Comment #3 Steve Moore (85.95.108.225) -

Hello

Please be advised you can Contact Num in the uk at the following number;

Tel 0871 750 4020

Fax 0871 750 4021

Or email service.uk@num.com

Or Post to

Num (UK) Ltd

Unit 3 Fairfield Court

Seven Stars Industrial Estate

Coventry

CV3 4LJ

Comment #4 Prashant from India -

The problem seems to be with the Auto Card , as you say that there was a electric short circuit , there are EEPROMS in the auto card and probably due to the short circuit the data might have been deleted. You will have to reload the data in the Auto card.

Try first by just pressing the CHAR button on the processor board then on the crt a page comes there you have many options indicated , then press the option clear RAM then after that press shift and XOff key on the key board you will go back to the same page , then press option Initialise if even after this the Systems does not boot you will have to load the data in the Auto card

Comment #5 Osama Elhosieny (41.232.149.87) -

Dear sir

I need any information about what happen if I take the processor or memory board from one machine and put it on anther machine? Where I have 4 machines with controller NUM750

Best regard

Comment #6 Devendra Bakhshi (203.78.212.2) -

Dear Sir,

We have NUM control CNC P1040GC crush roll grinding machine.Recently this machine was rebuilt in UK and now we have this machine since 1 year.Today one of F Funtion key is not working and we are unable to run this machine.Please advice if there is service in india.

CNC System-P1040GC

CN NUM Power 1040

24VDC

Or.no.

Or no.-0005023889/0011000

Sr. No-218429

LCD Monitor

8.4"NUM

0209 206 209

18-36VDC:

0.75A (MAx)

Comment #7 Marco G. from U.S -

HELP!

I have a 1996 Pegasus 306 CNC on the front of my terminal it reads NUM 1060. It was working fine until we moved the machine to a different shop. Now when I boot the computer. It has bus error. There is red light on the des led which I think indicates a fault on the card. I already tried pressing raz button on power supply rack in the main rack but nothing.

Any suggestions will be appreciated.

Comment #8 jose (200.67.52.6) -

Help!

I`m working the cnc machine record 130 this have the NUM 1040 but in the remote card 16/16 we have fisical input but the output it`s off, in the screen of I/O showme that the output its ok!

any comments will be appreciate.

thanks.

Comment #9 RAVI_MATE (203.145.134.195) -

Dear sir,

as you discuss in this article that you have 4 machines with controller NUM750, if you replace any one of card i.e memory or process card then alarm will displaced on crt unit "RE-Initilise Table , Press Y or N .

if you press y than all your machine parameter will vanish.

you can replace two card i.e. memory card & personality module at a time (small pcb card on process card) .

thanks

Ravidas Mate

Comment #10 Chris (2) from Greece -

Hello,

I have a CNC NUM 1062W for glass cutting.

The two(2) internal 1, 2V ni-cd battery wend under voltage.

I replaced then with new one and the machine asked for RAM clear.

I answered YES and after this step the machine has no program inside.

I have a PC connected with the NUM 1062W. Does any one know how to reprogramm the CNC from the PC or any other way?

I think a have the backup program to my PC.

Thanks a lot.

Name:           
E-Mail:         

Optional (please add to our directory first)
Web Link:       
Link Title:     

Message:

Note: once you register your email address with CNC Machine it is used across our whole network of forums and blogs. You can create seperate profiles for each forum or blog, but use the same login.